公司新聞
冷再生機租賃時打滑的原因及方法？
來源：http://www.622410.cn/ 日期：2020-09-24
求租冷再生機時打滑的原因及方法和優點有哪些，接下來小編將帶大家一起來了解下，希望以下的介紹可以讓大家更好的了解在運用時會出現的一些問題，希望對大家有所幫助?？蛻粼?strong>冷再生機租賃使用過程中，不可避免地會出現消耗和磨損，其中，冷再生機輸送帶特別容易出現問題，運行時間長，可能出現打滑現象，影響工作效率。讓冷再生機租賃廠家帶我們一起來分析下打滑的原因和解決辦法。
I hope that you can understand the advantages and disadvantages of the recycling machine when you use it. In the process of leasing and using the cold regenerator, the customers will inevitably suffer from consumption and wear. Among them, the conveyor belt of the cold regenerator is particularly prone to problems, and the running time is long, which may cause slipping phenomenon, affecting the work efficiency. Let the cold recycling machine rental manufacturers to take us together to analyze the causes of slip and solutions.
1、初始張力太小。
1. The initial tension is too small.
輸送帶離開滾筒的張力不夠，會引起皮帶打滑。一般來說，這種情況是在啟動時發生的。如果你想解決它，你必須調整張力裝置和增加初始張力。
The tension of the conveyor belt leaving the drum is not enough, which will cause the belt to slip. In general, this happens at startup. If you want to solve it, you have to adjust the tension device and increase the initial tension.
2、摩擦力是不夠的。
2. Friction is not enough.
傳動滾筒與輸送帶之間的摩擦力不足以引起滑動。造成這種現象的主要原因是輸送帶上的水或環境潮濕。解決方法：在氣缸中加入一些松香末。注意不要用手而應用鼓風設備吹入，以免發生事故。
The friction between the drive drum and the conveyor belt is not enough to cause sliding. The main reason for this phenomenon is the water on the conveyor belt or the environment is humid. Solution: add some rosin powder into the cylinder. Pay attention not to blow in by hand with blowing equipment to avoid accidents.
3、軸承損壞
3. Bearing damage
尾部滾子軸承損壞或不旋轉。造成損壞的原因是機器尾部太浮、太沉，不能及時修理和更換損壞的或不靈活的部件，這導致由打滑引起的阻力增加。
The tail roller bearing is damaged or does not rotate. The reason for the damage is that the tail of the machine is too floating and heavy to repair and replace the damaged or inflexible parts in time, which leads to the increase of resistance caused by slipping.
4、起步太快。
4. Starting too fast.
起動速度太快，不能打滑。這個時候可慢速啟動。如果使用鼠籠電機，則可以移動兩次，然后被激活，還可以有效地克服打滑現象。
The starting speed is too fast to slip. You can start it slowly at this time. If the squirrel cage motor is used, it can be moved twice and then activated, and the slip phenomenon can be effectively overcome.
5、輸送帶負荷過大。
5. The belt is overloaded.
輸送帶的負荷過大，超過電機能力也會打滑。打滑的優點是保護電機。否則，電動機將長期燃燒。但對于運行來說則是打滑事故。
If the load of the conveyor belt is too large, it will slip if it exceeds the capacity of the motor. The advantage of slipping is to protect the motor. Otherwise, the motor will burn for a long time. But for operation, it is a slip accident.
以上是關于冷再生機租賃時打滑的原因及方法的介紹，希望對大家有所幫助，感謝您的閱讀，如想了解更多內容歡迎點擊我們的http://www.622410.cn官網。
The above is about the reason and method of cold regenerator slipping when leasing. I hope it will help you. Thank you for your reading. If you want to know more, please click our http://www.622410.cn Official website.
公司地址：濟南市槐蔭區經一路273號群盛華城2號樓1-404
公司名稱：山東途暢路橋工程有限公司 
備案號：