撒布車控制頁面的調試

　　Debugging of the control page for the spreading vehicle

　　獨立控制系統

　　Independent control system

　　水泥撒布車系列產品擁有獨立的3路或5路粉料撒布分配系統，每套系統可獨立工作。撒鋪寬度范圍0.8~2.5米，以0.8米為單位任意調節，每套系統每平方米1-40公斤之間任意調節，解決了施工粉料重復覆蓋帶來的浪費。

　　The cement spreader series products have independent 3-way or 5-way powder spreading distribution systems, and each system can work independently. The spreading width range is 0.8-2.5 meters, which can be adjusted arbitrarily in units of 0.8 meters. Each system can adjust between 1-40 kilograms per square meter, solving the waste caused by repeated coverage of construction powder.

　　操作便捷，以車載控制器為核心運算單元，通過駕駛倉中的液晶顯示屏設置撒布車量，操作人員只需輸入撒鋪的重量與欒杜，系統會自動計算相關參數進行撒鋪工作。

　　Easy to operate, with the onboard controller as the core computing unit, the amount of spreading vehicle is set through the LCD display screen in the driver's cabin. The operator only needs to input the spreading weight and weight, and the system will automatically calculate the relevant parameters for spreading work.

　　下面，小編帶大家了解撒布車控制頁面的使用情況。

　　Next, the editor will take you to understand the usage of the control page for the spreader.

　　1

　　one

　　參數項目選定：

　　Parameter item selection:

　　在“主頁”界面下，當按下“撒布”按鈕，進入“撒布控制”界面，如下圖一所示；旋轉右上角“旋轉按鈕”選擇需要調整的參數項目，選中的項目用“矩形框”圈出，如下圖二所示；下按用于確認需要調整的參數項目。

　　In the "Home" interface, when the "Spread" button is pressed, enter the "Spread Control" interface, as shown in Figure 1 below; Rotate the "Rotate Button" in the upper right corner to select the parameter item that needs to be adjusted. Circle the selected item with a "Rectangular Box" as shown in Figure 2; Press to confirm the parameter items that need to be adjusted.

　　2

　　two

　　撒布量數值設定：

　　Distribution quantity value setting:

　　選定“撒布量設定”參數項目，旋轉右上角“旋轉按鈕”選擇需要修改的數值的位置，按下旋鈕確定，此時該數值消隱顯示，如下圖三所示；左旋“旋轉按鈕”變更數值大?。▊渥ⅲ鹤笮龜?shù)值從0-9循環變化），下按旋鈕確定。按照上述操作步驟，可以變更數據框中任意位置的數值，無論怎么調節，一定要保留中間位置的小數點；數值調好后，按下保存鍵保存，可先返回主頁，再次返回到撒布量數值設定頁面確認，以避免出現保存不上的情況出現。

　　Select the "Spread Quantity Setting" parameter item, rotate the "Rotate Button" in the upper right corner to select the position of the value that needs to be modified, press the knob to confirm, and the value will be hidden and displayed, as shown in Figure 3 below; Rotate the left rotation button to change the numerical value (note: the left rotation value changes cyclically from 0-9), press the knob down to confirm. According to the above steps, you can change the value at any position in the data box. No matter how you adjust it, be sure to keep the decimal point in the middle position; After adjusting the values, press the save button to save. You can first return to the homepage and then return to the spreading amount value setting page to confirm, in order to avoid situations where the values cannot be saved.

　　3

　　three

　　材料密度數值設定：

　　Material density numerical setting:

　　選定“材料密度”參數項目，旋轉右上角“旋轉按鈕”選擇需要修改的數值的位置，下按旋鈕確定，此時該數值消隱顯示，如下圖四所示；左旋“旋轉按鈕”變更數值大?。▊渥ⅲ鹤笮龜?shù)值從0-110循環變化），按下旋鈕確定。按照上述操作步驟，可以變更數據框中任意位置的數值。

　　Select the "Material Density" parameter item, rotate the "Rotate Button" in the upper right corner to select the position of the value to be modified, press the knob down to confirm, and the value will be displayed in a hidden state, as shown in Figure 4 below; Rotate the left rotation button to change the numerical value (note: the left rotation value changes cyclically from 0-110), press the knob to confirm. By following the above steps, you can change the value at any position in the data box.

　　材料密度的調整會影響到稱重報警，裝料時應根據實際物料比重情況進行裝載物料，嚴禁超負荷裝載物料。

　　The adjustment of material density will affect the weighing alarm. When loading, the material should be loaded according to the actual proportion of the material, and overloading is strictly prohibited.

　　以SLD390車型為例，如材料密度在“110”的狀態下車輛重量報警數值為18T，將“110”調節到“120”，此時的重量報警數值為19.6T(大約值，以實際為準）；將“110”調節到“90”，此時的重量報警數值為14.8T(大約值，以實際為準）。

　　Taking the SLD390 model as an example, if the material density is at "110" and the vehicle weight alarm value is 18T, adjusting "110" to "120" will result in a weight alarm value of 19.6T (approximately, subject to actual conditions); Adjust "110" to "90", and the weight alarm value at this time is 14.8T (approximately, subject to actual value).

　　需要特別注意的一點是，如材料密度數值調節到“100”以下，最前位數值應為“0”，以材料密度:“90”為例，應調節為“090”。

　　It should be noted that if the material density value is adjusted to below "100", the leading value should be "0". Taking the material density of "90" as an example, it should be adjusted to "090".

　　本文由  水泥撒布車出租  友情奉獻.更多有關的知識請點擊  http://www.622410.cn/   真誠的態度.為您提供為全面的服務.更多有關的知識我們將會陸續向大家奉獻.敬請期待.

　　This article is a friendly contribution from a cement spreader rental For more related knowledge, please click http://www.622410.cn/ Sincere attitude To provide you with comprehensive services We will gradually contribute more relevant knowledge to everyone Coming soon.